Full replacement
Pipe Bursting
A bursting head splits the old pipe outward while pulling a new HDPE pipe into the same path — total replacement, two small pits.
CIPP Pipe Lining in Ohio
A resin-saturated liner is installed inside the old pipe and cured hard, forming a new jointless pipe within a pipe.
Cured-in-place pipe lining rebuilds a failing sewer from the inside. A felt or fibreglass liner saturated with thermoset resin is pulled or inverted into the existing pipe, pressed tight against the wall, and cured until it hardens into a continuous new pipe inside the old one.
It has been the dominant sewer rehabilitation method worldwide since the technology was introduced in 1971, for one reason: it replaces the pipe's function without replacing the pipe's location. No trench across the lawn, no demolished driveway, no excavation under the foundation.
Lining Ohio's clay tile laterals
Clay tile is the ideal lining candidate and Ohio has a great deal of it. The clay itself is chemically stable and usually still structurally sound; what has failed is the joints between sections. A cured liner bridges every joint on the run at once, producing a continuous jointless pipe with nothing for roots to enter.
This is why lining tends to be the answer in Ohio's older neighbourhoods and why the results hold up — you are not patching a deteriorating material, you are eliminating the specific failure mode that clay tile has.
What makes a lined pipe better than the one it replaced
- No joints. The liner is continuous end to end. Joints are where roots enter, where groundwater infiltrates and where clay pipe fails — a lined pipe has none.
- Smoother bore. Cured resin has a lower friction coefficient than old clay or tuberculated cast iron, so flow often improves even though internal diameter is marginally reduced.
- Corrosion proof. The resin does not rust, rot or scale the way cast iron and Orangeburg do.
- Structural. A properly specified liner is designed to stand as a pipe in its own right, not merely to coat the host.
- Long design life. 50 years is the common benchmark. Municipalities using CIPP on public sewers routinely cite 50 to 100 years of extended service life.
The limitation you need to understand
CIPP needs a host pipe to line. The liner takes the shape of whatever it is pressed against, which means the existing pipe has to be intact enough to hold that shape while the resin cures.
Lining is the wrong method when the line has fully collapsed, when a section of pipe is simply missing, when the pipe has deformed badly out of round, or when a severe belly means the liner would cure a permanent low spot into place. Thoroughly deteriorated Orangeburg frequently falls into this category — it has lost its shape and there is nothing sound to line.
In those cases the answer is pipe bursting, which replaces the pipe entirely and is also trenchless. Any company that recommends lining without running a camera first is not in a position to know which one you need.
The one question that decides your repair: is the host pipe structurally intact? If yes, line it. If it has collapsed, deformed or gone missing, burst it. Everything else — price, timeline, disruption — follows from that single answer, and only a camera inspection can give it.
How the liner is cured
Three curing methods are in common use. The right one depends on diameter, length, access and site conditions:
- Ambient cure. The resin hardens at ground temperature. Simplest, no heat equipment, slowest — several hours and temperature-sensitive.
- Hot water or steam cure. Heat is circulated through the liner to accelerate the reaction. The common choice for residential laterals; typically a few hours.
- UV cure. A light train is drawn through a glass-fibre liner. Fastest and most controllable, with the best consistency, but needs more equipment and suits larger-diameter work.
Access: one or two small openings, not a trench
Most residential lining jobs are done through an existing cleanout. Where there is no usable access, we create a single small opening — a fraction of the excavation a dig-and-replace job requires.
That is the whole economic argument for trenchless. Conventional replacement of a lateral running under a mature lawn, a concrete driveway and a front walkway means restoring all three. The restoration frequently costs more than the pipe work. Lining leaves them untouched.
Protecting what is above the pipe
Ohio's established neighbourhoods are exactly where open-cut replacement hurts most: mature trees, decades-old lawns, brick walkways, and the deep front setbacks typical of pre-war platting, which mean a long lateral run under all of it.
Restoration on a trenched job across that frequently exceeds the cost of the pipe work. Lining leaves it untouched.
Note the limitation honestly: badly deteriorated Orangeburg — common in Ohio post-war construction — has usually lost the shape a liner needs to cure against. In those cases pipe bursting is the correct method and we will tell you so.
The process
How CIPP pipe lining is carried out
1
Inspect and measure
Camera survey establishes pipe material, diameter, length, defect locations and — the deciding factor — whether the host pipe can carry a liner.
2
Clean thoroughly
Jetting, root cutting and descaling as needed. Resin will not bond to a dirty wall, so this step is not optional.
3
Measure and wet out
The liner is cut to length and saturated with a measured resin volume under controlled conditions. Getting this wrong is the most common cause of a failed liner.
4
Install
The liner is inverted with air or water pressure, or winched into place, then pressed firmly against the host pipe wall.
5
Cure
Ambient, hot water, steam or UV depending on the specification. The liner hardens into a structural pipe.
6
Reinstate and verify
Any branch connections are reopened robotically, and a final camera pass documents the finished line. You get the footage.
Answers
CIPP Pipe Lining — frequently asked questions
How much does CIPP pipe lining cost?
Residential lateral lining commonly runs $4,000 to $20,000 all in. The variables are length, diameter, how many bends and connections are involved, how much cleaning the pipe needs first, and local permit requirements. It is typically competitive with — and often cheaper than — dig-and-replace once surface restoration is counted.
How long does the job take?
Most residential laterals are completed in one day. Larger or more complex jobs, and anything needing substantial descaling beforehand, can run two to three days. Service interruption is usually a few hours rather than the full job.
How long does a cured liner last?
50 years is the standard design benchmark, and municipalities applying CIPP to public sewers commonly cite 50 to 100 years of extended service life. Ask for the manufacturer's specification and the warranty in writing.
Does lining reduce my pipe's capacity?
Internal diameter is reduced slightly — typically a few millimetres of wall thickness. In practice flow usually improves, because the smooth cured surface has far less friction than the corroded cast iron or root-roughened clay it replaced.
Can every pipe be lined?
No, and this is the most important thing to be honest about. Lining needs a structurally intact host. Collapsed sections, missing pipe, severe deformation and badly deteriorated Orangeburg cannot be lined — those need pipe bursting. A camera inspection is the only way to tell.
Is it disruptive to my yard?
Minimally. Most jobs run through an existing cleanout, and where none exists we open one small access point. Lawns, driveways, mature trees, patios and walkways stay intact — which is the entire reason the method exists.
Keep reading
Related services in Ohio
Budget option
Sewer Spot Repair
One bad joint doesn't justify a whole new line. A sectional liner repairs just the damaged length.
Start here
Sewer Camera Inspection
A self-levelling camera runs the full line and shows you exactly what is wrong before anyone quotes a repair.